Lab Safety

Providing support, in the form of risk assessment, review, consultation(link sends e-mail), training, and the necessary resources and guidance for research at UC Berkeley.

Acetone Fire

July 31, 2008
What happened?

A student worker in a Berkeley campus laboratory was refilling squirt bottles with acetone from a larger dispensing container when he spilled approximately one cup of acetone liquid onto the floor. Due to lack of training, and/or an error in judgment, the student lit the acetone with a match to burn it off instead of following proper spill clean-up procedures. While doing so, the student accidentally knocked over another uncapped squirt bottle on the benchtop that was filled with acetone. This additional acetone ignited and set-off the fire sprinklers in the room,...

Oleylamine Chemical Burn

December 31, 2008
Office of Environment, Health, and Safety
What happened? A laboratory researcher suffered a delayed chemical burn after only a few drops of a highly corrosive organic chemical splattered on his unprotected left forearm. The burns first appeared hours after exposure, got worse overnight, and eventually required treatment at a hospital.

forearm with spotted chemical burns

The researcher's forearm

...

Pressurized Dewar Cap is Blown Off and Causes Minor Injury

February 28, 2009
Office of Environment, Health, and Safety
What happened?

In July 2008, a guest scientist at the Lawrence Berkeley National Laboratory sustained a minor injury when the cap of a 50-Liter liquid nitrogen Dewar burst off and hit his forehead. The scientist needed to fill the Dewar - which hadn't been used for several months - and assumed it was depressurized because of its lack of use.

Without wearing safety goggles or a face shield, the scientist attempted to verify the Dewar was depressurized by pulling a pressure relief plug. The relief plug was not designed to be manually operated (it did not have a pull ring), and it is...

Lab Fire Caused By Hotplate Heating Oil Bath That Injured Researcher

March 31, 2013
Office of Environment, Health, and Safety
What Happened?

A chemistry researcher was using an older model hot plate to heat an oil bath to 120-150°F. He borrowed the hotplate from someone else and was not familiar with the temperature controls. On this particular hot plate the temperature dial could go around from “LO” to “OFF” and back to “HI” heat. The researcher thought he had turned the hotplate “OFF” but it was still in the “ON” position and 30 minutes later the mineral oil bath ignited.

Fortunately, the oil bath was in a fume hood which kept the flames and fire inside the hood, it was reasonably clean and no other...

Ethanol Fire Burns Researcher

July 31, 2011
Office of Environment, Health, and Safety
What Happened?

A researcher was plating bacteria onto a petri dish using ethanol and a Bunsen burner as part of a standard sterile transfer on a lab bench. The metal spreader was dipped in a jar of ethanol and burned off in the burner. Somehow, the jar of ethanol spilled on the lab bench and onto the researcher's bare arms and t-shirt, and caught fire. The flames were reported to be up to two feet high. The researcher immediately went to the safety shower, pulled the handle which activated the emergency shower and got in. The shower water quickly put out the fire and cooled...

Corrosive Waste Spill

August 31, 2015
Office of Environment, Health, and Safety
What Happened?

A UC Berkeley researcher was working in a lab with a highly corrosive sulfuric acid and hydrogen peroxide (piranha) solution to clean the surface of a glass sample in a fume hood.

After completing the work, the researcher found the existing waste container to be greater than 75 percent full. Rather than add the recently used piranha solution to the already overfilled waste container, the researcher found an additional empty waste container and attempted to pour off some of the overfilled waste into the empty bottle.

During this attempt, some of the corrosive...

Eye Exposure to Specular Reflection

July 31, 2015
Office of Environment, Health, and Safety
What happened?

A researcher was diagnosing a power loss from a Spectra Physics 3900 Ti-Sapphire (oscillator) that is pumped by a Spectra Physics Millennia eV DPSS laser. During this procedure, they noticed some leakage in the form of a slight green diffuse light being emitted from the end of the metal tube connecting the DPSS pump laser to the Ti-Sapphire laser. The researcher attempted to re-adjust the beam tube to eliminate the leakage to improve the beam tube alignment. As he touched the beam tube, it became dislodged from its mounting, striking the 532 nm laser beam as it fell, causing...

Glove Selection Guide

Follow these steps to choose the appropriate type of protective glove for your job. The Glove Selection Chart also provides advantages and disadvantages for specific glove types. This guidance was prepared for laboratory researchers but may also be helpful for other people working with hazardous materials.

Once selected, glove use requirements for your lab should be posted in your Chemical Hygiene Plan flipchart under the Standard Operating Procedures section.See below for the...

Karina Saravia-Butler

Communications & Program Manager
Administration
Communications & Outreach
New PI Orientation
Lab Safety
Database Management

Construction Inspection Checklist - Lab Supplement

Office of Environment, Health & Safety